Material library and reference values
What the individual properties mean and how SpanDraft uses them in the calculation is described in the chapter Material properties. This chapter is about the material library and about how the fixed reference values of the built-in materials were selected.
Material library and project snapshot
The material library contains built-in and self-created materials. Built-in materials are read-only but can be copied as a starting point for a custom material.
When a material is added to a project, its current data set is stored in the project. The project then does not refer to the library entry. Later changes to the library therefore do not change projects that have already been saved.
Missing information in older projects is likewise not filled in automatically from the current library. A stored material thus remains exactly in the state in which it was added to the project.
An existing material note is stored as well. It describes the data set but has no influence on the calculation.
Built-in materials
The current material catalog contains eight materials in four groups. The groups serve only for classification.
| Material group | Material | Material number | Other designation |
|---|---|---|---|
| Structural steel | S235JR | 1.0038 | – |
| S355JR | 1.0045 | – | |
| Stainless steel | X5CrNi18-10 | 1.4301 | AISI 304 |
| X2CrNiMo17-12-2 | 1.4404 | AISI 316L | |
| Alloy steel | 42CrMo4 +QT | 1.7225 | – |
| 34CrNiMo6 +QT | 1.6582 | – | |
| Aluminum | AlMgSi0,5 T66 | 3.3206 | EN AW-6060 T66 |
| AlMg3 H22 | 3.3535 | EN AW-5754 H22 |
For each built-in material, exactly one fixed set of properties is stored. SpanDraft does not automatically choose other values if, for example, thickness, diameter, product form or temperature changes.
Every data set therefore needs a clear reference case. The following sections show the stored properties and explain why precisely this strength value and this reference value were chosen for the respective material.
Structural steel
S235JR — 1.0038
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 210 GPa | 7 850 kg/m³ | 0.30 |
The first thickness class up to 16 mm was taken as the basis for the fixed reference value. There the yield strength is 235 MPa and thus corresponds directly to the base value of grade S235. A lower value such as 225 MPa would already presuppose a greater product thickness, which SpanDraft does not know in the material data set.1
S355JR — 1.0045
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 210 GPa | 7 850 kg/m³ | 0.30 |
Here too, the first thickness class up to 16 mm is used as the reference. The yield strength of 355 MPa that applies there corresponds directly to the base value of grade S355. Lower values belong to greater thickness ranges and would not be more appropriate without a known component thickness.1
Stainless steel
X5CrNi18-10 — 1.4301
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 200 GPa | 7 900 kg/m³ | 0.30 |
For this austenitic stainless steel, is the strength value specified in EN 10088-3. For solution-annealed bars and sections, 190 MPa is given; the value remains the same across the listed thickness ranges up to 250 mm. 190 MPa is therefore suitable as a clear reference value without an additional thickness specification.2
X2CrNiMo17-12-2 — 1.4404
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 200 GPa | 8 000 kg/m³ | 0.30 |
For 1.4404 as well, EN 10088-3 specifies the strength via . For solution-annealed bars and sections, the minimum value is 200 MPa and remains unchanged across the listed thickness ranges. 200 MPa was therefore chosen as the fixed reference value.2
Alloy steel
42CrMo4 +QT — 1.7225
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 210 GPa | 7 800 kg/m³ | 0.30 |
For 42CrMo4 +QT, quenched and tempered round bar from 40 to 100 mm was defined as the reference case. For this range, a material data sheet according to DIN EN ISO 683-2 gives . The fixed value is thus based on a clearly delimited, common round bar range and not on the higher values of small or the lower values of large diameters.3
34CrNiMo6 +QT — 1.6582
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 210 GPa | 7 800 kg/m³ | 0.30 |
Quenched and tempered round bar from 40 to 100 mm was also chosen as the reference case. For this range, according to DIN EN ISO 683-2 is 800 MPa. The fixed value thus refers to the same clearly defined round bar range as for 42CrMo4 +QT.4
Aluminum
AlMgSi0,5 T66 — 3.3206
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 69 GPa | 2 700 kg/m³ | 0.33 |
For T66 sections, the data sheet gives up to 5 mm and 150 MPa for wall thicknesses above 5 up to 25 mm. Since the SpanDraft reference data set is to cover sections up to 25 mm, 150 MPa was chosen. In this way, the same value remains applicable across the entire chosen range.5
AlMg3 H22 — 3.3535
| Young’s modulus | Density | Poisson’s ratio | Strength value |
|---|---|---|---|
| 70 GPa | 2 670 kg/m³ | 0.33 |
For H22 sheet and plate, is constant at 130 MPa across all listed thickness ranges from above 0.2 to 40 mm. No additional selection between different thickness classes is necessary here; 130 MPa can therefore be used directly as the reference value.6
Limits of the reference values
Each built-in material represents the reference case described. SpanDraft does not automatically adjust their properties to other dimensions, product forms, temperatures or delivery and heat-treatment conditions.
If other properties govern a specific calculation, a custom material with the appropriate values can be created for it.
Sources
- Tata Steel. Warmgewalzt — Baustahl. Mechanische Eigenschaften nach EN 10025-2. Accessed .
- British Stainless Steel Association. Ambient temperature mechanical properties of austenitic stainless steel long products to BS EN 10088-3. BS EN 10088-3:2023. Accessed .
- Stahlwerk Augustfehn. Technical data sheet – 42CrMo4 (1.7225). Mechanical properties according to DIN EN ISO 683-2 (09/2018). 2024. Accessed .
- Stahlwerk Augustfehn. Technical data sheet – 34CrNiMo6 (1.6582). Mechanical properties according to DIN EN ISO 683-2 (09/2018). 2024. Accessed .
- Hydro Innovation & Technology. Technical datasheet — Extruded products, Alloy EN AW-6060. Hydro 6060_Rev.4; mechanical properties according to EN 755-2:2016. 2023. Accessed .
- thyssenkrupp Materials. Werkstoffdatenblatt EN AW-5754. 2017. Accessed .